| “This site contains affiliate links for which OEMDTC may be compensated” |
March 24, 2021 NHTSA CAMPAIGN NUMBER: 21V201000
Upper Control Arm Rear Axle Screw Not Tightened
A loose connection may fail, causing driving instability and increasing the risk of a crash.
NHTSA Campaign Number: 21V201
Manufacturer Porsche Cars North America, Inc.
Components SUSPENSION
Potential Number of Units Affected 7
Summary
Porsche Cars North America, Inc. (Porsche) is recalling certain 2019 Porsche 911 Speedster, 2020 Porsche 911 Carrera S Coupe, Carrera 4S Coupe, and Carrera S Cabriolet vehicles. The screw connection on the rear axle upper control arm may be loose.
Remedy
Porsche will notify owners, and dealers will rework and tighten the screw connection on the rear axle upper control arm, free of charge. Owner notification letters were mailed May 21, 2021. Owners may contact Porsche customer service at 1-800-767-7243. Porsche’s number for this recall is AMA6.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check if your Porsche has a Recall
AMA6 – Replacing Threaded Connections on Upper Control Arm on Rear Axle (Recall Campaign)
Order Type:
911 Carrera S (992)
911 Carrera 4S (992)
Model Year:
2020
Concerns:
Upper control arm to rear axle
Information:
There is a possibility that the threaded joints on the chassis securing the upper control arm to the rear axle were not tightened to the prescribed tightening torque on the affected vehicles.
Action required:
Replace threaded connections on upper control arm on rear axle.
Overview
The screw connection on the upper control arm of the rear axle might not be tightened according to specification.
If the screw connection fails it could cause a sudden driving instability with significant changes of the driving behavior and the potential loss of control.
The screw connection on the upper control arm will be reworked and tightened according to specification.
What is the issue?
The threaded joints securing the upper control arms to the rear axle of your vehicle may not be tightened according to the specification. If a connection fails it could potentially cause driving instability, increasing the risk of a crash.
What should you do?
Please contact any authorized Porsche dealer to schedule an appointment to have this recall performed as soon as possible, and to arrange for alternate transportation, if requested.
If prior to having this remedy performed you notice any abnormal noises coming from the rear axle of your vehicle, safely park your vehicle and immediately contact your authorized Porsche dealer.
To locate your nearest authorized Porsche dealer, visit: www.porsche.com/usa
What will Porsche do?
Porsche is conducting a safety recall to rework and tighten the affected screw connections between the rear axle and upper control arms. This remedy will be carried out free of charge.
SEOCONTENT-START
May 21, 2021
103303437 – 1
This notice applies to your vehicle:
WP0
This notice is sent to you in accordance with the National Traffic and Motor
Vehicle Safety Act. Porsche has decided that a defect that relates to
motor vehicle safety exists in certain 2019-2020 Model Year Porsche 911
Carrera S, 911 Carrera 4S and 911 Speedster vehicles. Our records show
that you are the current owner of a vehicle affected by this recall.
What is the issue?
The threaded joints securing the upper control arms to the rear axle of
your vehicle may not be tightened according to the specification. If a
connection fails it could potentially cause driving instability, increasing the
risk of a crash.
What should you do?
Please contact any authorized Porsche dealer
to schedule an appointment to have this recall
performed as soon as possible, and to arrange for
alternate transportation, if requested.
If prior to having this remedy performed you
notice any abnormal noises coming from the rear
axle of your vehicle, safely park your vehicle and
immediately contact your authorized Porsche
dealer.
To locate your nearest authorized Porsche dealer,
visit: www.porsche.com/usa
What will Porsche do?
Porsche is conducting a safety recall to rework and tighten the affected screw connections between the rear axle and
upper control arms. This remedy will be carried out free of charge.
This is an important Safety Recall.
The remedy will take up to one business day to perform, however depending on the dealer’s work schedule, it may be necessary to
make your vehicle available for a longer period of time.
Certain 2019-2020 Model Year Porsche 911 Carrera S, 911 Carrera 4S and 911 Speedster Vehicles
Rear Axle Upper Control Arm Connections
NHTSA ID 21V-201
IMPORTANT SAFETY RECALL
URGENT SAFETY RECALL
This is an important Safety Recall.
The remedy will be performed FREE
OF CHARGE to you.
Dear Mr. ,
Mr.
–
What if you are not the owner or operator of this vehicle?
If you are the lessor and registered owner of the vehicle identified in this action, the law requires you to forward this
letter immediately via first-class mail to the lessee within ten days of receipt. If you have changed your address or
sold the vehicle, please contact customer support so we can update our records.
Can we assist you further?
Please be aware that if you require any assistance in making an appointment to have this recall
performed, please call or write:
Porsche Cars North America, Inc.
Attn: Customer Support
One Porsche Drive
Atlanta, GA 30354
1-800-PORSCHE
customersupport@porsche.com
If you still cannot obtain satisfaction, and your dealer or Porsche is unable to remedy the defect
without charge or within a reasonable amount of time, you may file a complaint with:
Administrator
National Highway Traffic Safety Administration 1200 New Jersey Avenue, S.E.
Washington, D.C. 20590
or call the toll-free Vehicle Safety Hotline at 1-888-327-4236 (TTY: 1-800-424-9153) or go to
http:/ /www.safercar.gov.
We apologize for any inconvenience this matter may cause you. We are taking this action to help
ensure your safety and continued satisfaction with your vehicle.
Very truly yours,
Porsche Cars North America, Inc.
*****************************************************************************************************
4/15/2021 AMA6 Recall campaign – Replacing threaded conne… | PPN Portal
AMA6 Recall campaign –Replacing threaded connections onupper control arm on rear axle
Version 1
Overview
IMPORTANT REMINDER
AMA6 Recall campaign – Replacing threaded connectionson upper control arm on rear axle
IT IS A VIOLATION OF FEDERAL LAW FOR DEALERS TO DELIVER TO CUSTOMERS NEW VEHICLES INTHEIR INVENTORY AFFECTED BY THIS NOTIFICATION UNTIL THESE VEHICLES ARE REMEDIED.DEALERS SHOULD NOT SELL, LEASE, RENT, OR LOAN ANY NEW OR USED VEHICLES IN DEALERINVENTORY AFFECTED BY THIS NOTIFICATION PRIOR TO REMEDY. DEALERS GROUNDING LEASERETURNS SHOULD REMEDY ALL AFFECTED GROUNDED VEHICLES.
4/15/2021 AMA6 Recall campaign – Replacing threaded conne… | PPN Portal
Parts required
The screw connection on the upper control arm of the rear axle might not be tightened according tospecication.
If the screw connection fails it could cause a sudden driving instability with signicant changes of thedriving behavior and the potential loss of control.
The screw connection on the upper control arm will be reworked and tightened according tospecication.
Model type
911 Carrera S/4S (992)/911 Speedster (991)
Model year
2019 – 2020
Number
7
Part No.
Designation
Quantity/vehicle*
Parts return
WHT008727
Cheese head bolt,M10 x 1 x 46.5
Depends on the scope
No
PAF008735
Hexagon-head bolt,M12 x 1.5 x 95
Depends on the scope
No
N 90916701
Hexagon nut, M12 x1.5
Depends on the scope
No
9A700867700
Hexagon-head bolt,M12 x 1.5 x 80
Depends on the scope
No
PAF909664
Hexagon nut, M12 x1.5
Depends on the scope
No
PAF007957
Hexagon nut, M10
Depends on the scope
No
9A700781900
Hexagon nut, M12
Depends on the scope
No
PAF008673
Hexagon-head bolt,M12 x 1.5 x 110
Depends on the scope
No
WHT008740
Hexagon-head bolt,M12 x 1.5 x 40
Depends on the scope
No
WHT008676
Hexagon-head bolt,M12 x 1.5 x 45
Depends on the scope
No
4/15/2021 AMA6 Recall campaign – Replacing threaded conne… | PPN Portal
Warranty processing
Part No.
Designation
Quantity/vehicle*
Parts return
PAF008674
Hexagon ange bolt,M12 x 1.5 x 105
Depends on the scope
No
PAF008955
O-ring
Depends on the scope
No
992129260
Hose clamp
Depends on the scope
No
PAF009589
Hexagon-head bolt,M12 x 1.5 x 75
Depends on the scope
No
99908444501
Hexagon nut, M12 x1.5
Depends on the scope
No
99907285901
Hexagon-head bolt,M12 x 1.5 x 58
Depends on the scope
No
* Given that di
*************************************************************************************************
Technical Information
Service
61/21 ENU AMA6 4
AMA6 – Replacing Threaded Connections on Upper Control Arm on Rear Axle (Recall
Campaign)
Order Type:
Model Year:
Concerns:
Information:
911 Carrera S (992)
911 Carrera 4S (992)
2020
Upper control arm to rear axle
There is a possibility that the threaded joints on the chassis securing the upper control arm to
the rear axle were not tightened to the prescribed tightening torque on the affected vehicles.
Action required: Replace threaded connections on upper control arm on rear axle.
Information
Please note that different screw positions on the rear axle must be replaced on the affected vehicles.
The following specific campaign scopes have therefore been defined for replacing the threaded
connections. Every vehicle is clearly assigned just one campaign scope.
• Replacing bolts securing (front) upper control armto left wheel carrier
Scope 1: Technical Information ‘Scope 1: Screws for upper control arm (front) to left wheel carrier’
• Replacing bolts securing (front) upper control arm to right wheel carrier
Scope 2: Technical Information ‘Scope 2: Screws for upper control arm (front) to right wheel carrier’
• Replacing bolts securing (front) upper control arm to left rear-axle carrier side section
Scope 3: Technical Information ‘Scope 3: Threaded connection securing (front) upper control arm to
left rear-axle carrier side section’
• Replacing bolts securing (front) upper control arm to right rear-axle carrier side section
Scope 4: Technical Information ‘Scope 4: Threaded connection securing (front) upper control arm to
right rear-axle carrier side section’
• Replacing bolts securing (rear) upper control arm to left rear-axle carrier side section
Scope 5: Technical Information ‘Scope 5: Threaded connection securing (rear) upper control arm to
left rear-axle carrier side section’
• Replacing bolts securing (rear) upper control arm to right rear-axle carrier side section
AfterSales Apr 15, 2021
Page 1 of 16
Scope 6: Technical Information ‘Scope 6: Threaded connection securing (rear) upper control arm
to right rear-axle carrier side section’
Service 4 AMA6 ENU 61/21
Technical Information
Affected
vehicles:
Order Type:
Concerns:
Information:
Only vehicles assigned to the campaign (see also PCSS Vehicle Information). This campaign affects 7
vehicles.
911 Speedster (991)
2019
Upper control arm to rear axle
There is a possibility that the threaded joints on the chassis securing the upper control arm to
the rear axle were not tightened to the prescribed tightening torque on the affected vehicles.
Action required: Replace threaded connections on upper control arm on rear axle.
Information
Please note that different screw positions on the rear axle must be replaced on the affected vehicles.
The following specific campaign scopes have therefore been defined for replacing the threaded
connections. Every vehicle is clearly assigned just one campaign scope.
Scope 1-6: Only applies to 992 vehicles – see relevant Technical Information for these vehicle types.
• Replacing bolts securing (front) upper control armto left wheel carrier
Scope 7: Technical Information ‘Scope 7: Screws for upper control arm (front) to left wheel carrier’
• Replacing bolts securing (front) upper control arm to right rear-axle carrier side section
Scope 8: Technical Information ‘Scope 8: Threaded connection securing (front) upper control arm to
right rear-axle carrier side section’
• Replacing bolts securing (rear) upper control arm to left rear-axle carrier side section
Scope 9: Technical Information ‘Scope 9: Threaded connection securing (rear) upper control arm to
left rear-axle carrier side section’
• Replacing bolts securing (rear) upper control arm to right rear-axle carrier side section
Scope 10: Technical Information ‘Scope 10: Threaded connection securing (rear) upper control arm
to right rear-axle carrier side section’
Affected
Vehicles:
Only vehicles assigned to the campaign (see also PCSS Vehicle Information). This campaign affects 7
vehicles.
Apr 15, 2021
Page 2 of 16 AfterSales
Model Year:
Technical Information
Service
61/21 ENU AMA6 4
Parts required
Information
Due to the different bolts/screws to be replaced on the upper control arm on the rear axle of each vehicle,
the required fastening nuts and bolts are listed accordingly.
Technical Information ‘Warranty processing’
Required tools
Tools: • Torque wrench, 2–10 Nm (1.5–7.5 ftlb.), e.g. VAG 1783 Torque wrench, 2-10 Nm (1.5-7.5
ftlb.)
• Torque wrench, 6–50 Nm (4.5–37 ftlb.), e.g. VAG 1331A Torque wrench, 6-50 Nm (4.5-37
ftlb.)
• Torque wrench, 40–200 Nm (30–148 ftlb.), e.g. VAG 1332 Torque wrench, 40-200 Nm
(30-148 ftlb.)
• Electronic torque angle torque wrench, 2-100 Nm (1.5-74 ftlb.), e.g. 9768 – Electronic torque
wrench, 2 – 100Nm(1.5 – 74 ftlb.)
• Electronic torque angle torque wrench, 20-400 Nm (15-296 ftlb.), e.g. VAS 6942 Torque angle
torque wrench, 20-400 Nm (15-296 ftlb.)
All other required (special) tools in accordance with the linked Workshop Manuals depending on the
relevant assigned scope.
Scope 1: Screws for upper control arm(front) to left wheel carrier
Work Procedure: 1 On the left rear axle, replace the screwed connection for the upper control arm (front) to the wheel
carrier.
For instructions, see: Workshop Manual ‘42351951 Removing and installing upper control arm
(front)’
Mounting for upper control arm (front)
1.1 Loosen screw connection Mounting for
upper control arm (front) -2- for the upper
control arm (front) Mounting for upper
control arm (front) -1- to the wheel carrier,
then remove the fastening screw from the
upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 70 Nm(52 ftlb.) Final
tightening +180°
2 Enter the campaign in the Warranty and Maintenance
booklet.
AfterSales Apr 15, 2021
Page 3 of 16
Service 4 AMA6 ENU 61/21
Technical Information
End of action required
For warranty processing, see General information on warranty processing and Scope 1 under
Technical Information ‘42351951 Warranty processing’.
Scope 2: Screws for upper control arm (front) to right wheel carrier
Work Procedure: 1 On the right rear axle, replace the screwed connection for the upper control arm (front) to the
wheel carrier.
For instructions, see: Workshop Manual ‘42351951 Removing and installing upper control arm
(front)’
Mounting for upper control arm (front)
1.1 Loosen screw connection Mounting for
upper control arm (front) -2- for the upper
control arm (front) Mounting for upper
control arm (front) -1- to the wheel carrier,
then remove the fastening screw from the
upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 70 Nm(52 ftlb.) Final
tightening +180°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 2 under
Technical Information ‘42351951 Warranty processing’.
Scope 3: Threaded connection securing (front) upper control armto left rear-axle carrier side
section
Work Procedure: 1 On the left rear axle, replace the screwed connection for the upper control arm (front) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351951 Removing and installing upper control arm
(front)’
Apr 15, 2021
Page 4 of 16 AfterSales
Technical Information
Service
61/21 ENU AMA6 4
Mounting for upper control arm (front)
1.1 Loosen screw connection Mounting for
upper control arm (front) -3- for the upper
control arm (front) Mounting for upper
control arm (front) -1- to the rear axle carrier
side section, then remove the fastening
screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 70 Nm(52 ftlb.) Final
tightening +180°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 3 under
Technical Information ‘42351951 Warranty processing’.
Scope 4: Threaded connection securing (front) upper control arm to right rear-axle carrier side
section
Work Procedure: 1 On the right rear axle, replace the screwed connection for the upper control arm (front) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351951 Removing and installing upper control arm
(front)’
Mounting for upper control arm (front)
1.1 Loosen screw connection Mounting for
upper control arm (front) -3- for the upper
control arm (front) Mounting for upper
control arm (front) -1- to the rear axle carrier
side section, then remove the fastening
screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 70 Nm(52 ftlb.) Final
tightening +180°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 4 under
Technical Information ‘42351951 Warranty processing’.
AfterSales Apr 15, 2021
Page 5 of 16
Service 4 AMA6 ENU 61/21
Technical Information
Scope 5: Threaded connection securing (rear) upper control arm to left rear-axle carrier side
section
Work Procedure: 1 On the left rear axle, replace the screwed connection for the upper control arm (rear) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351953 Removing and installing upper control arm
(rear)’
Upper control arm (rear)
1.1 Loosen screw connection Upper control
arm (rear) -3- for the upper control arm (rear)
Upper control arm (rear) -1- to the rear
axle carrier side section, then remove the
fastening screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 70 Nm(52 ftlb.) Final
tightening +180°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 5 under
Technical Information ‘42351953 Warranty processing’.
Scope 6: Threaded connection securing (rear) upper control arm to right rear-axle carrier side
section
Work Procedure: 1 On the right rear axle, replace the screwed connection for the upper control arm (rear) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351953 Removing and installing upper control arm
(rear)’
Apr 15, 2021
Page 6 of 16 AfterSales
Technical Information
Service
61/21 ENU AMA6 4
Upper control arm (rear)
1.1 Loosen screw connection Upper control
arm (rear) -3- for the upper control arm (rear)
Upper control arm (rear) -1- to the rear
axle carrier side section, then remove the
fastening screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 70 Nm(52 ftlb.) Final
tightening +180°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 6 under
Technical Information ‘42351953 Warranty processing’.
Scope 7: Screws for upper control arm(front) to left wheel carrier
Work Procedure: 1 On the left rear axle, replace the screwed connection for the upper control arm (front) to the wheel
carrier.
For instructions, see: Workshop Manual ‘42351951 Removing and installing upper control arm
(front)’
Mounting for upper control arm (front)
1.1 Loosen screw connection Mounting for
upper control arm (front) -2- for the upper
control arm (front) Mounting for upper
control arm (front) -1- to the wheel carrier,
then remove the fastening screw from the
upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 90 Nm(67 ftlb.) Final
tightening +90°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 7 under
Technical Information ‘42351951 Warranty processing’.
AfterSales Apr 15, 2021
Page 7 of 16
Service 4 AMA6 ENU 61/21
Technical Information
Scope 8: Threaded connection securing (front) upper control arm to right rear-axle carrier side
section
Work Procedure: 1 On the right rear axle, replace the screwed connection for the upper control arm (front) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351951 Removing and installing upper control arm
(front)’
Mounting for upper control arm (front)
1.1 Loosen screw connection Mounting for
upper control arm (front) -3- for the upper
control arm (front) Mounting for upper
control arm (front) -1- to the rear axle carrier
side section, then remove the fastening
screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 90 Nm(67 ftlb.) Final
tightening +90°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 8 under
Technical Information ‘42351951 Warranty processing’.
Scope 9: Threaded connection securing (rear) upper control arm to left rear-axle carrier side
section
Work Procedure: 1 On the left rear axle, replace the screwed connection for the upper control arm (rear) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351953 Removing and installing upper control arm
(rear)’
Apr 15, 2021
Page 8 of 16 AfterSales
Technical Information
Service
61/21 ENU AMA6 4
Upper control arm (rear)
1.1 Loosen screw connection Upper control
arm (rear) -3- for the upper control arm (rear)
Upper control arm (rear) -1- to the rear
axle carrier side section, then remove the
fastening screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 90 Nm(67 ftlb.) Final
tightening +90°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 9 under
Technical Information ‘42351953 Warranty processing’.
Scope 10: Threaded connection securing (rear) upper control arm to right rear-axle carrier side
section
Work Procedure: 1 On the right rear axle, replace the screwed connection for the upper control arm (rear) to the rear
axle carrier side section.
For instructions, see: Workshop Manual ‘42351953 Removing and installing upper control arm
(rear)’
Upper control arm (rear)
1.1 Loosen screw connection Upper control
arm (rear) -3- for the upper control arm (rear)
Upper control arm (rear) -1- to the rear
axle carrier side section, then remove the
fastening screw from the upper control arm.
1.2 Insert new fastening screw, screw on new
fastening nut and tighten only in zero position
to avoid straining the bearings.
Initial tightening 90 Nm(67 ftlb.) Final
tightening +90°
2 Enter the campaign in the Warranty and Maintenance
booklet.
End of action required
For warranty processing, see General information on warranty processing and Scope 10
under Technical Information ‘42351953 Warranty processing’.
AfterSales Apr 15, 2021
Page 9 of 16
Service 4 AMA6 ENU 61/21
Technical Information
Warranty processing
Scope 1: Replacing bolts securing (front) upper control arm to left wheel carrier
Threaded connection of upper control arm (front) at left wheel carrier
Includes: Removing and installing rear left wheel
Labor time: 42 TU
Required part numbers: Designation
– Use
Qty.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Upper control arm (rear) to wheel carrier
1 ea.
PAF909664 Hexagon nut, M12 x 1.5
– Upper control arm (rear) to wheel carrier
1 ea.
Damage Code AMA6 099 000 2
Scope 2: Replacing bolts securing (front) upper control arm to right wheel carrier
Threaded connection of upper control arm (front) to right wheel carrier
Includes: Removing and installing rear right wheel
Labor time: 42 TU
Required part numbers: Designation
– Use
Qty.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Upper control arm (rear) to wheel carrier
1 ea.
PAF909664 Hexagon nut, M12 x 1.5
– Upper control arm (rear) to wheel carrier
1 ea.
Damage Code AMA6 099 000 2
Apr 15, 2021
Page 10 of 16 AfterSales
Technical Information
Service
61/21 ENU AMA6 4
Replacing threaded connection of upper control arm (front) to left rear-axle
carrier side section
Includes: Removing and installing left and right rear wheels
Removing and installing left and right rear axle carriers
Removing and installing left and right control arms
Removing and installing left and right struts
Removing and installing left and right rear cover
Removing and installing center cover
Measuring vehicle at front and rear
Adjusting vehicle at rear
Labor time: 517 TU
Required part numbers: Designation
– Use
Qty.
WHT008727 Cylinder screw, M10 x 1 x 46.5
– Drive shaft to final drive
6 ea.
PAF008735 Hexagon head bolt, M12 x 1.5 x 95
– Side section to body
– Outer rear axle carrier to body
4 ea.
N 90916701 Hexagon nut, M12 x 1.5
– Side section to body
1 ea.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Upper control arm (front) to side section
1 ea.
PAF909664 Hexagon nut, M12 x 1.5
– Upper control arm (front) to side section
3 ea.
PAF007957
or
9A700781900
Hexagon nut, M10
or
Hexagon nut, M12
– Actuator/coupling link to
suspension/stabilizer
2 ea.
PAF008673 Hexagon-head bolt M12 x 1.5 x 110
– Inner rear axle carrier to body
2 ea.
WHT008740 Hexagon head bolt, M12 x 1.5 x 40
– Front strut to body
2 ea.
WHT008676 Hexagon-head bolt, M12 x 1.5 x 45
– Rear strut to rear axle carrier
2 ea.
PAF008674 Hexagon flange bolt, M12 x 1.5 x 105
– Lower control arm to rear wheel carrier
2 ea.
AfterSales Apr 15, 2021
Page 11 of 16
Scope 3: Replacing bolts securing (front) upper control arm to left rear-axle carrier side section
Damage Code AMA6 099 000 2
Service 4 AMA6 ENU 61/21
Technical Information
Scope 4: Replacing bolts securing (front) upper control arm to right rear-axle carrier side section
Replacing threaded connection of upper control arm (front) to right
rear-axle carrier side section
Includes: Removing and installing left and right rear wheels
Removing and installing left and right rear axle carriers
Removing and installing left and right control arms
Removing and installing left and right struts
Removing and installing left and right rear cover
Removing and installing center cover
Measuring vehicle at front and rear
Adjusting vehicle at rear
Labor time: 517 TU
Required part numbers: Designation
– Use
Qty.
WHT008727 Cylinder screw, M10 x 1 x 46.5
– Drive shaft to final drive
6 ea.
PAF008735 Hexagon head bolt, M12 x 1.5 x 95
– Side section to body
– Outer rear axle carrier to body
4 ea.
N 90916701 Hexagon nut, M12 x 1.5
– Side section to body
1 ea.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Upper control arm (front) to side section
1 ea.
PAF909664 Hexagon nut, M12 x 1.5
– Upper control arm (front) to side section
3 ea.
PAF007957
or
9A700781900
Hexagon nut, M10
or
Hexagon nut, M12
– Actuator/coupling link to
suspension/stabilizer
2 ea.
PAF008673 Hexagon-head bolt M12 x 1.5 x 110
– Inner rear axle carrier to body
2 ea.
WHT008740 Hexagon head bolt, M12 x 1.5 x 40
– Front strut to body
2 ea.
Apr 15, 2021
Page 12 of 16 AfterSales
Technical Information
Service
61/21 ENU AMA6 4
WHT008676 Hexagon-head bolt, M12 x 1.5 x 45
– Rear strut to rear axle carrier
2 ea.
PAF008674 Hexagon flange bolt, M12 x 1.5 x 105
– Lower control arm to rear wheel carrier
2 ea.
Damage Code AMA6 099 000 2
Scope 5: Replacing bolts securing (rear) upper control arm to left rear-axle carrier side section
Removing and installing bolts securing upper control arm (rear) to left rear
axle carrier side section
Includes: Removing and installing rear left wheel
Removing and installing left intake pipe
Removing and installing rear left wheel housing liner (rear
section)
Labor time: 75 TU
Required part numbers: Designation
– Use
Qty.
PAF909664 Hexagon nut, M12 x 1.5
– Upper control arm (rear) to side section
1 ea.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Upper control arm (rear) to side section
1 ea.
PAF008955 O-ring
– Pressure pipe to turbocharger
1 ea.
992129260 Hose clamp
– Pressure pipe to turbocharger
1 ea.
Damage Code AMA6 099 000 2
Scope 6: Replacing bolts securing (rear) upper control arm to right rear-axle carrier side section
Removing and installing bolts securing upper control arm (rear) to right
rear axle carrier side section
Includes: Removing and installing rear right wheel
Removing and installing right intake pipe
Removing and installing rear right wheel housing liner (rear
section)
Labor time: 73 TU
AfterSales Apr 15, 2021
Page 13 of 16
Service 4 AMA6 ENU 61/21
Technical Information
Required part numbers: Designation
– Use
Qty.
PAF909664 Hexagon nut, M12 x 1.5
– Upper control arm (rear) to side section
1 ea.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Upper control arm (rear) to side section
1 ea.
PAF008955 O-ring
– Pressure pipe to turbocharger
1 ea.
992129260 Hose clamp
– Pressure pipe to turbocharger
1 ea.
Damage Code AMA6 099 000 2
Warranty processing
Scope 1-6: Only applies to 911 Carrera (992) vehicles – see relevant Technical Information for these vehicle types.
Scope 7: Replacing bolts securing (front) upper control arm to left wheel carrier
Threaded connection of upper control arm (front) at left wheel carrier
Includes: Removing and installing rear left wheel
Labor time: 59 TU
Required part numbers: Designation
– Use
Qty.
PAF009589 Hexagon-head bolt, M12 x 1.5 x 75
– Upper control arm (front) to wheel carrier
1 ea.
99908444501 Hexagon nut, M12 x 1.5
– Upper control arm (front) to wheel carrier
1 ea.
Damage Code AMA6 099 000 2
Apr 15, 2021
Page 14 of 16 AfterSales
Technical Information
Service
61/21 ENU AMA6 4
Replacing screws for upper control arm (front) to right rear axle carrier
side section
Includes: Removing and installing left and right rear wheel
Removing and installing rear-axle cross member
Removing and installing engine guard
Removing and installing left and right struts
Removing and installing support plate
Removing and installing cover for rear underbody
Complete suspension measurement
Labor time: 340 TU
Required part numbers: Designation
– Use
Qty.
PAF009589 Hexagon-head bolt, M12 x 1.5 x 75
– Upper control arm (front) to side section
1 ea.
99908444501 Hexagon nut, M12 x 1.5
– Upper control arm (front) to side section
– Side section to upper rear axle carrier
– Side section on lower rear axle carrier
5 ea.
PAF008735 Hexagon-head bolt M12 x 1.5 x 95
– Side section to body
2 ea.
N 90916701 Hexagon nut, M12 x 1.5
– Side section to body
1 ea.
PAF008673 Hexagon-head bolt M12 x 1.5 x 110
– Inner rear axle carrier to body
2 ea.
9A700867700 Hexagon-head bolt, M12 x 1.5 x 80
– Lower side section to rear axle carrier
2 ea.
99907285901 Hexagon-head bolt, M12 x 1.5 x 58
– Upper side section to rear axle carrier
2 ea.
WHT008740 Hexagon head bolt, M12 x 1.5 x 40
– Front strut to body
2 ea.
WHT008676 Hexagon-head bolt, M12 x 1.5 x 45
– Rear strut to rear axle carrier
2 ea.
Damage Code AMA6 099 000 2
AfterSales Apr 15, 2021
Page 15 of 16
Scope 8: Replacing bolts securing (front) upper control arm to right rear-axle carrier side section
Service 4 AMA6 ENU 61/21
Technical Information
Replacing bolts securing upper control arm (rear) to left rear axle carrier
side section
Includes: Removing and installing rear left wheel
Labor time: 59 TU
Required part numbers: Designation
– Use
Qty.
99908444501 Hexagon nut, M12 x 1.5
– Upper control arm (rear) to side section
1 ea.
PAF008735 Hexagon-head bolt, M12 x 1.5 x 95
– Upper control arm (rear) to side section
1 ea.
Damage Code AMA6 099 000 2
Scope 10: Replacing bolts securing (rear) upper control arm to right rear-axle carrier side section
Replacing bolts securing upper control arm (rear) to right rear axle carrier
side section
Includes: Removing and installing rear right wheel
Labor time: 59 TU
Required part numbers: Designation
– Use
Qty.
99908444501 Hexagon nut, M12 x 1.5
– Upper control arm (rear) to side section
1 ea.
PAF008735 Hexagon-head bolt, M12 x 1.5 x 95
– Upper control arm (rear) to side section
1 ea.
Damage Code AMA6 099 000 2
Important Notice: Technical Bulletins issued by Porsche Cars North America, Inc. are intended only for use by professional automotive technicians who have attended Porsche service training
courses. They are written to inform those technicians of conditions that may occur on some Porsche vehicles, or to provide information that could assist in the proper servicing of a vehicle. Porsche special
tools may be necessary in order to perform certain operations identified in these bulletins. Use of tools and procedures other than those Porsche recommends in these bulletins may be detrimental to the
safe operation of your vehicle, and may endanger the people working on it. Properly trained Porsche technicians have the equipment, tools, safety instructions, and know-how to do the job properly and
safely. Part numbers listed in these bulletins are for reference only. The work procedures updated electronically in the Porsche PIWIS diagnostic and testing device take precedence and, in the event of a
discrepancy, the work procedures in the PIWIS Tester are the ones that must be followed. © 2021 Porsche Cars North America, Inc.
Apr 15, 2021
Page 16 of 16 AfterSales
Scope 9: Replacing bolts securing (rear) upper control arm to left rear-axle carrier side section
SEOCONTENT-END
2 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| PORSCHE | 911 | 2019 |
| PORSCHE | 911 CARRERA | 2020 |
9 Associated Documents
Recall Quarterly Report #1, 2021-2
RCLQRT-21V201-5435.PDF 211.143KB
Loading...
Reload document 
Open in new tab
Defect Notice 573 Report
RCLRPT-21V201-3703.PDF 216.413KB
Loading...
Recall Acknowledgement
RCAK-21V201-3506.pdf 644.946KB
Loading...
Part 577 Owner Notification Envelope
Loading...
ISSUED Owner Notification Letter(Part 577)
RCONL-21V201-7842.pdf 127.04KB
Loading...
Remedy Instructions and TSB
Loading...
Manufacturer Notices(to Dealers,etc) – 4/15/2021 AMA6 Recall campaign Replacing threaded connections on upper control arm on rear axle Version 1
Loading...
Recall Quarterly Report #2, 2021-3
RCLQRT-21V201-1636.PDF 211.244KB
Loading...
Recall Quarterly Report #3, 2021-4
RCLQRT-21V201-1025.PDF 211.327KB
Loading...
Latest Recalls Documents
For the Latest and Most Recent Recalls Information Visit the link below…
https://www-odi.nhtsa.dot.gov/acms/cs/documentList.xhtml?docId=21V201&docType=RCL
- COMPATIBILITY – Fits 2003-2009 Porsche Cayenne; 2007-2017 Volkswagen Touareg
- GET THE RIGHT PART -- Before purchasing, research to ensure that the part will fit your vehicle; enter all vehicle information (year, make, model, engine and trim) for compatibility and check qualifier notes
- PREMIUM MATERIALS -- Made from high-quality natural rubber material for durability and ride performance
- EXTENDED SERVICE LIFE -- Less prone to splitting, discoloring or cracking with age for long life
- HIGHLY PRECISE ENGINEERING -- Optimized for quiet operation and helps to inhibit wear, salt, road grime and oils
- Grand Cherokee Air Suspension Control Valve Block Air Supply
- Replacement for Porsche 97035815302, 970-358-153-02, 958-698-014-A, 958-358-903-00, 95835890300; Replacement for Jeep 68087233AA; Replacement for VW AUDI 7L0698014C, 7L0698014, 7L0-698-014-C
- Replacement for Jeep Grand Cherokee 2011-2019; Replacement for Porsche Cayenne 2011-2019; Panamera 2010-2016
- Replacement for VW Touareg 2004-2010; Replacement for Audi Q7 2007-2015
- Warranty for 12 Months
- PART NUMBER:4L0698007C; 4L0698007C; 7L8616006A; 7L8616006; 7L8616007A; 7L8616007; 7L8616006C; 7L8616007C; 7L8616007E; 7L8616007F; 7L0698853A; 7L0698853; 95535890101;95535890104;95535890103;95535890102
- REPLACEMENT FOR:Porsche Cayenne 2003-2010 all engine ; VolksWagen Touareg 2004-2010 all engine
- QUALITY:Excellent materials and manufacturing technology, beyond the original factory quality, 100% test before shipment, and we provide a 12-month warranty
- CHARACTERISITICS:The use of new technology and the best materials makes the air pumping faster and the noise lighter, which is a different experience.
- KINDLY REMINDER:Please confirm the vechile models and part number before order.Installing by a professional is recommended.
- Direct replacement - fits and performs like the original equipment on specific vehicles
- Reliable fit - precision-engineered to match the design and dimensions of original components
- Durable construction - manufactured to strict standards using sturdy, safe materials
- Rigorously tested - thorough quality control measures ensure longevity
- Ensure fit - to make sure this part fits your exact vehicle, input your make, model and trim level into the garage tool
- VEHICEL COMPATIBLE - Control Arm Kit compatible with 2007 2008 Audi Q7 | 2003-2008 Porsche Cayenne | 2004-2009 Volkswagen Touareg
- OEM/ PART NUMBER - Control Arm Kit compatible with 7L0407151C, 7L0407152C, 7L0407151C, 7L0407151D, 7L0407151E, 7L0407151H, 7L0407152D, 7L0407152E, 7L0407152H, 7L0 407 151 C, 7L0 407 151 D, 7L0 407 151 E, 7L0 407 151 H, 7L0 407 152 D, 7L0 407 152 E, 7L0 407 152 H
- NOTICE - Please verify Fitment or Application, make sure our part will perfectly match for the original car before purchasing!
- DIRECT FIT - Direct replacement for a proper fit and easy installation. Quality materials used, meets or exceeds OEM standards, every product must take inspected and tested multiple times before the shipment.
- WARRANTY - Aftermarket product order from Bapmic, we offer 5 Years Warranty, true worry-free shopping experience.
- FIT for: Air Suspension Compressor fit for Porsche for Panamera 2010-2016
- OE PART NUMBER:97035815110, 97035815111
- BENEFIT: Extensive performance examinations, including charging time, current and solenoid operation are performed on each unit to ensure reliable, consistent performance
- FUNCTION: Air Suspension Compressor solves excessive suspension sags and restores vehicle handling
- ATTENTION: Air suspension compressors can be installed quickly and easily in minutes, providing a comfortable and efficient experience. If you have any questions, please contact us as soon as possible.
- [Vehicle Fitment]: Compatible with Porsche Panamera 2010-2016 Hatchback
- [Reference Number]: 97034305212, 97034305214, 97034305215, 97034305216, 97034305217, 97034305219, 97034305222, 97034305234, 9703430523, 97034305208, 97034305209, 97034305210, 97034305211
- [Installation Position]: Front Right, Passenger Side
- [Advantages]: Air suspension struts allow for easier adjustment of both ride height and stiffness to accommodate different loads, road conditions, or driving preferences, improving ride comfort by absorbing shock and reducing vibration more effectively
- [Buy with Confidence]: A-Premium offers a one-year unlimited-mileage guarantee on our meticulously crafted air suspension strut. We offer a wide variety of automotive accessory categories, ensuring that you can hit the road with peace of mind.
- High pressure nitrogen regulator, Fill the entire vehicle air suspension system with nitrogen ,compatible with Porsche Cayenne Paramela ，with two special joints 9825 00072198250
- The regulator body is made of forged brass, with all brass connections and components, full size regulator-2 inch pressure gauge with rubber protector,Unique size hose connector, compatible with Porsche Cayenne Paramela air suspension,
- The regulator has two clear and easy-to-read pressure gauges. The side pressure gauge measures the nitrogen pressure in the AC system and displays the degree. The top pressure gauge has a clear display that lets you know how much nitrogen is left in the gas tank, so you don’t have to worry about running out suddenly.
- Note: When the vehicle is raised, close the air suspension, use PIWIS TEST to exhaust and refill the replaced valve spring (pressure: +7bar+1bar), and the replacement of a new valve spring must be refilled (with nitrogen), and special Tool disassembly
- Service: ZKTOOL is committed to providing the best professional tools and best service for auto repair. If you have any questions, please contact us. We provide 24-hour before and after sales service
Last update on 2024-04-06 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.