AH01 – Replacing Fastening Screws for Fuel Collection Pipes – 2017 Porsche

“This site contains affiliate links for which OEMDTC may be compensated”

NHTSA Campaign Number: 17V054
Manufacturer Porsche Cars North America, Inc.
Components FUEL SYSTEM, GASOLINE
Potential Number of Units Affected 4,090

 

Fuel Leak due to Sheared Fastening Screws

A fuel leak in the presence of an ignition source increases the risk of a fire.

 

Summary

Porsche Cars North America, Inc. (Porsche) is recalling certain 2017 911 Carrera, 911 Carrera S, 911 Carrera 4, 911 Carrera 4S, 911 Targa 4, 911 Targa 4S + GTS, 911 Carrera Cabriolet, 911 Carrera S Cabriolet, 911 Carrera 4 Cabriolet, 911 Carrera 4S Cabriolet, 718 Boxster, 718 Boxster S, 718 Cayman, and 718 Cayman S vehicles.

The screws that fasten the fuel collection pipes in the engine compartment may shear off, resulting in a fuel leak.

 

Remedy

Porsche will notify owners, and dealers will install improved fastening screws, free of charge.

The manufacturer has not yet provided a notification schedule.

Owners may contact Porsche customer service at 1-800-767-7243.

Porsche’s number for this recall is AH01.

 

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

 

Check if your Porsche has a Recall

 

Technical Information Service

2

13/17 ENU AH01 2

 

AH01 – Replacing Fastening Screws for Fuel Collection Pipes (Stop-Sale Campaign)

Vehicle Type: 718 Boxster (982)/718 Boxster S (982)
Model Year: 2017
Subject: Fastening screws for fuel collection pipes
Concern: There is a possibility that the fastening screws for the fuel collection pipes on the affected vehicles can shear off due to stress corrosion cracking.

If this happens, the high fuel pressure that builds up in the fuel injection system when the engine is running can press the relevant fuel collection pipe off the fuel injectors. This can cause a fuel leak in the engine compartment.

Remedial Action: Replace fastening screws for both fuel collection pipes.
Parts Info: NOTE:  NECESSARY PARTS FOR THIS CAMPAIGN ARE STILL BEING MANUFACTURED AND ARE EXPECTED TO ARRIVE CW07.  ONCE THE REQUIRED PARTS FOR THIS CAMPAIGN HAVE ARRIVED,

PCNA WILL BEGIN THE AUTOMATIC ALLOCATION PROCESS FOR UP TO 50% OF THE VEHICLES THAT ARE SERVICED AT YOUR DEALERSHIP.  APPROXIMATELY 45 DAYS AFTER YOUR FIRST ALLOCATION, YOUR DEALER WILL AUTOMATICALLY BE ALLOCATED AN ADDITIONAL 30% OF THE REQUIRED PARTS FOR THE VEHICLES THAT ARE STILL IN NEED OF REPAIR.

 

Installation
Position:

Overview of installation position (shown on 718 Boxster as an example)Overview of installation position (shown on 718 Boxster as an example)

1 – Fuel collection pipe

2 – Fastening screws (replace)

Affected
Vehicles:
Only the vehicles assigned to the campaign (see also PIWIS Vehicle information). This campaign affects 4,518 vehicles in North America.

 

Parts required

Parts Info: Part No. Designation – Use Qty.
000 043 306 00 Torx screw, BM 6 x 85

– Fuel collection pipe

4 ea.
999 076 053 01 ⇒Hexagon nut, M10 – Rear diagonal brace 8 ea.
999 072 840 01 ⇒Hexagon-head bolt, M10 x 35

– Diagonal brace to body

2 ea.
N 908 484 05 ⇒Hexagon nut, M12 x 1.5 – Engine carrier to engine mount 2 ea.

 

Required tools

Tools:
  • Torque/torque angle screw tool, 20 – 400 Nm (15 – 296 ftlb.), e.g. VAS 6942 – Torque/torque angle screw tool
  • VAS 6918 – Quick-Clamping Unit
  • 9229/1 – Puller hook
  • Plastic assembly wedge (commercially available)
If the wheel alignment values must be corrected during suspension alignment, the following tools will also be required:
  • 9730 – Socket-wrench insert
  • 9847 – Socket-wrench insert
  • VAS 6430/1A – Setting Device with Reflector
  • VAS 6430/3 – ACC reflector mirror
  • VAS 6190/2 – T-bar Setting Tool for ACC Sensor

 

Preparatory work

Work Procedure:

  1. Raise the vehicle on a lifting platform Workshop Manual ‘4X00IN Lifting the vehicle’.
  2. Move convertible top to service position Workshop Manual ‘6101IN Convertible-top service position’.
  3. Relieve fuel pressure in the system.

3.1 Remove cover on the fuse carrier in the passenger compartment at the front left.

3.2 Pull out fuse for fuel pump.

The fuse (20 A) is in row B ⇒Fuse carrier in passenger compartment at the front left -1-, slot FB5 ⇒Fuse carrier in passenger compartment at the front left -2-.

Fuse carrier in passenger compartment at the front leftFuse carrier in passenger compartment at the front left

 

WARNING

Exhaust gases

  • Risk of Carbon Monoxide (CO) Poisoning

⇒Before starting the engine, position an exhaust extraction system behind the vehicle’s exhaust pipes and switch it on.

3.3 Start the engine and leave it running at idle speed until it cuts out.

This can take up to 5 minutes.

3.4 Switch off ignition and remove ignition key.

3.5 Re-insert fuse for fuel pump.

  1. Disconnect ground line at the battery Workshop Manual ‘2X00IN Work instructions after disconnecting the battery.
  2. Remove trim panel for convertible top compartment Workshop Manual ‘700819 Removing and installing trim panel for convertible top compartment/engine compartment lid.
  3. Remove engine compartment lid Workshop Manual ‘557819 Removing and installing engine compartment lid.
  4. Remove air cleaner housing Workshop Manual ‘242519 Removing and installing air cleaner housing’.
  5. Remove rear wheels Workshop Manual ‘440519 Removing and reinstalling wheel.
  6. Remove cover for rear underbody Workshop Manual ‘519419 Removing and installing cover for rear underbody’.
  7. Remove diagonal braces on the rear axle Workshop Manual ‘421320 Removing and installing struts.

 

Replacing fastening screws for fuel collection pipes

Work Procedure:

  1. Lowering the engine to complete other work.

1.1 Loosen fastening nuts Turning tailpipe cover -2- on both clamps Turning tailpipe cover -1- for the tailpipe cover and turn the tailpipe cover as far as required until the tailpipes are pointing downwards.

Information

  • The weight must be distributed uniformly on the oil pan.
  • Never apply localised pressure to the oil pan

Turning tailpipe coverTurning tailpipe cover

 

1.2 Support the engine at the oil pan using a suitable transmission jack.

Information

  • When lowering the engine, it must not rest on the rear-axle cross member.
  • The exhaust system must not touch against the body or rear apron when lowering it.
  • Always be careful of hoses, lines and cables when lowering the system!
  • Always avoid collisions!

1.3 Lower the engine as far as required until the fastening screws for the fuel collection pipes are accessible.

For instructions, see Workshop Manual ‘1001IN Lowering the engine to complete other work’.

 

  1. Replace fastening screws for fuel collection pipes.

2.1 Loosen and unscrew front fastening screw Replacing fastening screws -2- (viewed in direction of travel) for fuel collection pipe on cylinder 1–3 Replacing fastening screws -1-.

2.2 Screw in and tighten new fastening screw, Part No. 000 043 306 00.

Tightening torque 13 Nm (9.5 ftlb.)

2.3 Loosen and unscrew rear fastening screw Replacing fastening screws -3- for fuel collection pipe on cylinder 1–3 Replacing fastening screws -1-.

2.4 Screw in and tighten new fastening screw, Part No. 000 043 306 00.

Tightening torque 13 Nm (9.5 ftlb.)

2.5 Repeat steps 3.1 to 3.4 on the fuel collection pipe on cylinder 4–6 Replacing fastening screws -4- in order to replace the fastening screws Replacing fastening screws -5 and 6-.

Replacing fastening screwsReplacing fastening screws

 

  1. Raise the engine to installation position and secure it.

For instructions, see Workshop Manual ‘1001IN Lowering the engine to complete other work’.

  1. Turn tailpipe cover into installation position and align it with respect to the rear apron. Then secure the tailpipe cover.

For instructions, see Workshop Manual ‘263519 Removing and installing tailpipe cover’.

 

Concluding work

Work Procedure:

  1. Install diagonal braces on the rear axle Workshop Manual ‘421320 Removing and installing struts.
  2. Install cover for rear underbody Workshop Manual ‘519419 Removing and installing cover for rear underbody’.
  3. Install rear wheels Workshop Manual ‘440519 Removing and reinstalling wheel.
  4. Install air cleaner housing Workshop Manual ‘242519 Removing and installing air cleaner housing’.
  5. Install engine compartment lid Workshop Manual ‘557819 Removing and installing engine compartment lid.
  6. Install trim panel for convertible top compartment Workshop Manual ‘700819 Removing and installing trim panel for convertible top compartment/engine compartment lid.
  7. Connect ground line for battery Workshop Manual ‘2X00IN Work instructions after disconnecting the battery.
  8. Bleed the high-pressure side of the fuel system.

8.1 Connect a battery charger or power supply, suitable for AGM type batteries, recommended current rating of 70A fixed voltage 13.5V to 14.5V.

First connect the positive cable of the charger to the positive terminal of the battery and then connect the negative cable of the charger to the ground point for jump-lead starting External power connection.

Then switch on the battery charger and start charging the battery.

External power connectionExternal power connection

 

8.2 Switch on the ignition.

8.3 Connect the PIWIS Tester to the vehicle communication module (VCI) via the USB cable. Then connect the communication module to the vehicle and switch on the PIWIS Tester.

8.4 On the PIWIS Tester start screen, call up the ‘Diagnostics’

The vehicle type is then read out, the diagnostic application is started and the control unit selection screen is populated.

8.5 Bleed the high-pressure side of the fuel system using the PIWIS Tester Workshop Manual ‘200107 Bleeding fuel system on high-pressure side – First start function’.

8.6 Read out and erase the fault memory Workshop Manual ‘033500 Fault memory for on-board diagnosis.

Information

If control units are found to have faults that are not related to this workshop campaign, these must be found and corrected separately. This work cannot be invoiced under the workshop campaign number.

8.7 Switch off the ignition.

8.8 Disconnect the PIWIS Tester from the vehicle.

8.9 Switch off and disconnect the battery charger.

  1. Move convertible top out of service position Workshop Manual ‘6101IN Convertible-top service position’.
  2. Remove the vehicle from the lifting platform.
  3. Perform suspension alignment and make adjustments.

Workshop Manual ‘449503 Suspension alignment, complete’

Workshop Manual ‘4495TW Adjustment values for suspension alignment’

  1. After correcting the wheel alignment values, carry out the following required subsequent work.

12.1 Calibrate steering-angle sensor Workshop Manual ‘456005 Initialising and calibrating PSM steering-angle sensor.

12.2 Teach steering lock settings for the power-steering gear Workshop Manual ‘489025 Power-steering gear: Teaching steering lock settings’.

12.3 If installed: Calibrate control unit for distance measuring sensor (ACC)Workshop Manual ‘278515 Adjusting control unit for distance measuring sensor’.

12.4 If installed: Calibrate front camera.

For instructions, see Workshop Manual ‘963855 Replacing front camera’.

  1. Enter the campaign in the Warranty and Maintenance booklet.

 

References:

Workshop Manual ‘033500 Fault memory for on-board diagnosis

Workshop Manual ‘1001IN Lowering the engine to complete other work’

Workshop Manual ‘2X00IN Work instructions after disconnecting the battery

Workshop Manual ‘200107 Bleeding fuel system on high-pressure side – First start function’

Workshop Manual ‘242519 Removing and installing air cleaner housing’

Workshop Manual ‘263519 Removing and installing tailpipe cover’

Workshop Manual ‘278515 Adjusting control unit for distance measuring sensor’

Workshop Manual ‘4X00IN Lifting the vehicle’

Workshop Manual ‘421320 Removing and installing struts

Workshop Manual ‘440519 Removing and installing wheel

Workshop Manual ‘4495TW Adjustment values for suspension alignment’

Workshop Manual ‘449503 Suspension alignment, complete’

Workshop Manual ‘456005 Initialising and calibrating PSM steering-angle sensor

Workshop Manual ‘489025 Power-steering gear: Teaching steering lock settings’

Workshop Manual ‘519419 Removing and installing cover for rear underbody’

Workshop Manual ‘557819 Removing and installing engine compartment lid

Workshop Manual ‘6101IN Convertible-top service position’

Workshop Manual ‘700819 Removing and installing trim panel for convertible top compartment/engine compartment lid

Workshop Manual ‘963855 Replacing front camera’

 

Warranty processing

Information:

Scope 1 – Scope 6: Not relevant for this vehicle type.

Information

The working times specified below were determined specifically for carrying out this campaign and may differ from the working times published in the Labor Operation List in PIWIS.

Scope 7:

Replacing fastening screws for fuel collection pipes

Vehicle equipment:

Working time: Replacing fastening screws for fuel collection pipes Labor time: 465 TU
Includes: Raising and lowering the vehicle

Moving convertible top into service position

Reducing fuel pressure

Disconnecting and connecting battery

Removing and installing trim panel for convertible top compartment

Removing and installing engine compartment lid

Removing and installing air cleaner housing

Removing and installing rear wheels

Removing and installing cover for rear underbody

Removing and installing diagonal braces

Loosening and securing tailpipe cover

Loosening and securing engine

Connecting and disconnecting battery charger

Connecting and disconnecting PIWIS Tester

Bleeding fuel high-pressure system

Reading out and erasing fault memory

Performing suspension alignment and making adjustments

Calibrating steering-angle sensor

Teaching steering lock settings

Without: Calibrating control unit for distance measuring sensor

Calibrating front camera

Parts required:
000 043 306 00 Torx screw, BM 6 x 85

– Fuel collection pipe

4 ea.
999 076 053 01 Hexagon nut, M10

– Rear diagonal brace

8 ea.
999 072 840 01 Hexagon-head bolt, M10 x 35

– Diagonal brace to body

2 ea.
N 908 484 05 Hexagon nut, M12 x 1.5

Engine carrier to engine mount

2 ea.
Damage Code AH01 099 000 2

 

Scope 8:

Replacing fastening screws for fuel collection pipes

Vehicle equipment:

  • Adaptive cruise control ACC (I-no. 456) and/or front camera (I-no. 631, 632 or 852)
Working time: Replacing fastening screws for fuel collection pipes Labor time: 515 TU
Includes: Raising and lowering the vehicle

Moving convertible top into service position

Reducing fuel pressure

Disconnecting and connecting battery

Removing and installing trim panel for convertible top compartment

Removing and installing engine compartment lid

Removing and installing air cleaner housing

Removing and installing rear wheels

Removing and installing cover for rear underbody

Removing and installing diagonal braces

Loosening and securing tailpipe cover

Loosening and securing engine

Connecting and disconnecting battery charger

Connecting and disconnecting PIWIS Tester

Bleeding fuel high-pressure system

Reading out and erasing fault memory

Performing suspension alignment and making adjustments

Calibrating steering-angle sensor

Teaching steering lock settings

Calibrating control unit for distance measuring sensor

Calibrating front camera

Parts required:
000 043 306 00 Torx screw, BM 6 x 85

– Fuel collection pipe

4 ea.
999 076 053 01 Hexagon nut, M10

– Rear diagonal brace

8 ea.
999 072 840 01 Hexagon-head bolt, M10 x 35

– Diagonal brace to body

2 ea.
N 908 484 05 Hexagon nut, M12 x 1.5

Engine carrier to engine mount

2 ea.
Damage Code AH01 099 000 2

 

https://static.nhtsa.gov/odi/rcl/2017/RCRIT-17V054-3957.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [356.10 KB]

 

 

Leave a Comment

Share to...